Effect of welding polarity on iron dilution, clad chemistry, and interfacial microstructure in multilayer SMAW Inconel 625 overlays on SA-387 grade 11 steel en en High-strength steels used in the oil and gas industry are susceptible to corrosion in harsh environments. Although Inconel 625 offers excellent corrosion resistance, its high cost limits large-scale application. Weld cladding with Inconel 625 provides a cost-effective alternative; however, excessive dilution with the steel substrate increases iron content and degrades clad chemistry. This study investigates the effect of welding polarity on iron dilution and clad chemistry in multilayer SMAW Inconel 625 overlays deposited on SA-387 grade 11 steel. Three-layer claddings were produced using direct current electrode negative (DCEN) and direct current electrode positive (DCEP) polarities. Clad chemistry was characterized by positive material identification (PMI) and scanning electron microscopy with energy-dispersive X-ray spectroscopy (SEM-EDS). Iron dilution was calculated from measured iron contents. Under the investigated conditions, the DCEN clad exhibited substantially lower iron content (3.97 ± 0.12 wt%) compared with the DCEP clad (10.6 wt%). DCEN also permitted a lower welding current (100–120 A versus 140–150 A for DCEP), resulting in reduced heat input. These findings demonstrate that DCEN polarity can effectively minimize iron dilution and produce clad chemistry closer to that of the Inconel 625 filler metal. Corrosion performance was not directly evaluated in this study and remains a subject for future investigation. 203 211 Majid Haghighi Borujeni Material Expert, Machine Sazi Arak, Arak Iran Iman Mohammadi Head of Welding and Material Department, Machine Sazi Arak, Arak Iran Fardin Nematzadeh Department of Advanced Materials, Materials and Energy Research Center, Karaj Iran f.nematzadeh@merc.ac.ir Dilution Inconel 625 Weld cladding Polarity Vol 6 No 3 Paper 3.pdf [1] J.F.M. Costa, J.C.F. Jorge, L.F.G. de Souza, M.C. Mendes, H.N. Farneze, H.A.Y. Magalhães, Microstructural evaluation of Inconel 625 weld cladding deposited by the GMAW and GMAW with rotating electrode processes, Technol. Metal. Mater. Min. 21 (2024) e2848. https://doi.org/10.4322/2176-1523.20242848. ##[2] A.B. Cunha, J. Vatavuk, C.R.C. Lima, Investigating the effects of iron dilution on the corrosion resistance of Inconel 625 welding overlay on carbon steel, Materials. 18 (2025) 5574. https://doi.org/10.3390/ma18245574. ##[3] M. Rozmus-Górnikowska, M. Blicharski, J. Kusiński, Influence of weld overlaying methods on microstructure and chemical composition of Inconel 625 boiler pipe coatings, Kovove Mater. 52 (2014) 141–147. https://doi.org/10.4149/km-2014-3-141. ##[4] R.J. Macedo, C. de Azevedo Celente, D. Souza, H.L. Costa, Effects of the shielding gas and substrate thickness on dilution and microstructure of Inconel® 625 MIG/MAG welded coatings, J. Braz. Soc. Mech. Sci. Eng. 46 (2024) 458. https://doi.org/10.1007/s40430-024-05041-3. ##[5] J.T.M. de Hosson, J.L. de Mol van Otterloo, Surface engineering with lasers: Application to Co-based materials, Surf. Eng. 13 (1997) 471–481. https://doi.org/10.1179/sur.1997.13.6.471. ##[6] P.P.B. da Silva, I. dos Santos Araújo, M.R.S. Vieira, S.L. Urtiga Filho, Influence of welding parameters on the geometric and microstructural characteristics of Inconel 625 coatings deposited on ASTM A36 steel by plasma transferred arc, Matéria. 25 (2020) e1050. https://doi.org/10.1590/S1517-707620200002.1050. ##[7] R.A. Lorenzoni, R.P. Gasparini, A.C. dos Santos, T. de Sousa Luz, M.C.S. de Macêdo, A study on the intergranular corrosion and pitting resistance of Inconel 625 coating by PTA-P, Corros. Eng. Sci. Technol. 54 (2019) 62–74. https://doi.org/10.1080/1478422X.2018.1533677. ##[8] A.X. dos Santos, T.M. Maciel, J.D. Costa, M.B. de Sousa, S. Prasad, et al., Study on influence of the PTA-P welding process parameters on corrosion behavior of Inconel 625 coatings, Matéria. 24 (2019) e0619. https://doi.org/10.1590/S1517-707620190001.0619. ##[9] C.P. Alvarães, F.C.A. Madalena, L.F.G. de Souza, J.C.F. Jorge, L.S. Araújo, M.C. Mendes, Performance of the Inconel 625 alloy weld overlay obtained by FCAW process, Matéria. 24 (2019) e12290. https://doi.org/10.1590/S1517-707620190001.0627. ##[10] L. Guo, H. Zheng, S. Liu, Y. Li, X. Xu, C. Feng, Formation quality optimization and corrosion performance of Inconel 625 weld overlay using hot wire pulsed TIG, Rare Met. Mater. Eng. 45 (2016) 2219–2226. https://doi.org/10.1016/S1875-5372(17)30006-1. ##[11] M.J. Moradi, M. Ketabchi, An experimental study of microstructure and mechanical behavior of Alloy 625 weld overlay deposited on ASTM A516 Grade 70, Indian J. Sci. Technol. 8 (2015) 1–6. https://doi.org/10.17485/ijst/2015/v8i12/70725. ##[12] P. Elango, S. Balaguru, Welding parameters for Inconel 625 overlay on carbon steel using GMAW, Indian J. Sci. Technol. 8 (2015) 1–5. https://doi.org/10.17485/ijst/2015/v8i31/84309. ##[13] A. Kourdani, R.D. Haghighi, Evaluating the properties of dissimilar metal welding between Inconel 625 and 316L stainless steel by applying different welding methods and consumables, Metall. Mater. Trans. A. 49 (2018) 1453–1467. https://doi.org/10.1007/s11661-018-4469-7. ##[14] M. Kumar, R. Shrimali, A.K. Singh, S. Pandey, Effect of welding current and electrode polarity on weld bead geometry and shape relationships in gravity-assisted mechanized contact shielded metal arc welding, Recent Advances, Materials and Manufacturing, Springer. (2024) 215–225. https://doi.org/10.1007/978-981-97-3654-6_22. ##[15] A. Aloraier, K. Al-Fadhalah, A.M. Paradowska, E. Alfaraj, Effect of welding polarity on bead geometry, microstructure, microhardness, and residual stresses of 1020 steel, J. Eng. Res. 2 (2014) 137–160. https://doi.org/10.7603/s40632-014-0029-5. ##[16] J.-S. Kim, Y.-I. Park, H.-W. Lee, Effects of heat input on the pitting resistance of Inconel 625 welds by overlay welding, Met. Mater. Int. 21 (2015) 350–355. https://doi.org/10.1007/s12540-015-4245-9. ##[17] L. Xu, C. Shao, L. Tian, J. Zhang, Y. Han, et al., Intergranular corrosion behavior of Inconel 625 deposited by CMT/GTAW, Corros. Sci. 201 (2022) 110295. https://doi.org/10.1016/j.corsci.2022.110295. ##[18] H. Kumar, G. Suresh, M. Krishnamoorthy, Microstructural evaluation and corrosion behaviour of Inconel 82 and Inconel 625 overlays on 304L stainless steel weld used in nuclear fuel reprocessing plant, Proc. Inst. Mech. Eng. L: J. Mater. Des. Appl. 238 (2024) 1358–1367. https://doi.org/10.1177/14644207231224169. ##[19] V.B. Trindade, E.S. Souza, J.M.A. de Paula, M.C.M. de Souza Costa, G.L. de Faria, Effect of different heat treatments on microstructure and microhardness of a C-Mn steel/Inconel 625 coating system, Technol. Metal. Mater. Min. 14 (2017) 167–174. https://doi.org/10.4322/2176-1523.1182. ##[20] T.J. Antoszczyszyn, R.M.G. Paes, A.S.C.M. de Oliveira, A. Scheid, Impact of dilution on the microstructure and properties of Ni-based 625 alloy coatings, Soldag. Inspeção. 19 (2014) 134–144. https://doi.org/10.1590/0104-9224/SI1902.05. ##[21] K. Song, Z.-J. Wang, S. Hu, S. Zhang, E. Liang, Welding current influences on Inconel 625/X65 cladding interface, Mater. Manuf. Process. 33 (2018) 770–777. https://doi.org/10.1080/10426914.2017.1364851. ##[22] P.K. Nachimuthu, S. Gosipathala, R.K. Arasappan, S.S. Nallathambi, High temperature corrosion performance of Inconel 625 hard overlays deposited on stainless steel substrate, Mater. Corros. 75 (2024) 875–890. https://doi.org/10.1002/maco.202314032. ##[23] American Welding Society (AWS), Welding Handbook, 9th ed., Vol. 4, Materials and Applications, Part 1, American Welding Society, Miami, FL. (2011). ##[24] B.-C. Goo, J.-W. Seo, Y.-J. Lee, Effect of welding polarity on mechanical properties of submerged arc welded railway vehicle wheels, Metals. 12 (2022) 1381. https://doi.org/10.3390/met12081381. ##[25] L. Dong, Z. Shi, Y. Zhang, S. Wang, Q. Wang, L. Liu, Microstructure and sulfide stress corrosion cracking of the Inconel 625/X80 weld overlay fabricated by cold metal transfer process, Int. J. Hydrog. Energy. 47 (2022) 29113–29130. https://doi.org/10.1016/j.ijhydene.2022.06.210. ##[26] J. Li, C. Li, S. Guo, L. Cheng, Y. Lei, et al., Degradation mechanism of hot corrosion resistance in Inconel 625 arc cladding layers induced by substrate Fe dilution in molten salt, Mater. Lett. 421 (2026) 141101. https://doi.org/10.1016/j.matlet.2026.141101. ##[27] D. Ferreira Filho, D. Souza, J.L. Gonçalves Júnior, R.P. Reis, W.M. da Silva Junior, A.F. Tavares, Influence of substrate on the tribological behavior of Inconel 625 GMAW overlays, Coatings. 13 (2023) 1454. https://doi.org/10.3390/coatings13081454.